For home improvement, after the water and gas acceptance is completed, the next step is to turn the bricklayer into the market. The bricklayer project involves the layout of the home structure, and it also includes such large projects as kitchen tiles. Then, what are the processes in the construction of the masonry? What are the details? How to carry out the construction management of the masonry?
Be prepared before laying bricks
As we all know, bricklayers are a kind of work for interior decoration, and it is the most important stage. It is mainly responsible for the construction of cement bricks, including building masonry, masonry partitions, cement mortar plastering, floor leveling, and tile paving. Post and so on. The laying of the floor tiles requires preparation in advance and takes the longest time.
Ma Kai, the designer of Senzhong Decoration Co., said that the front wall of the floor tile should have a good horizontal line, the toilet water storage test should be qualified, and the direction of the paving pattern should be examined; when the wall tile is laid, it should be noted whether the water circuit of the waterproof layer has been accepted. The position of the waist line tile is determined, whether the wall brick corner is added.
When laying bricks, first the wall behind the ground
The tiling procedure is the first wall and the back of the wall, and the wall is laid from the bottom to the top. Pay attention to these details before laying. For example, the floor tiles in the living room and hall should be laid in the last two times when the paint is not brushed. The specific method is: first check the color number and quality of the floor tiles, and secondly, if the floor tiles need to soak water, they should be treated according to different materials.
In addition, there are some important points to be paid during the laying process: pre-layout bricks, indoor paving bricks without design requirements when the joint width is 1~1.5 mm, non-whole bricks should be placed at the secondary or female corners, using special sewing cards . The elastic line is used to find the ground elevation according to the indoor standard horizontal line, calculate the number of vertical and horizontal blocks according to the area of ​​the tiling, level with the horizontal ruler, and eject the horizontal and vertical control lines of the wall brick. Dip bricks and wet walls: Before laying the tiles, soak the bricks in clean water for more than two hours, then take them out to dry, and soak them in 2% warm water in winter. The back of the brick is covered with mortar, and the sides are scraped into a bevel. Note that the corners are full of pulp. It is also necessary to pay attention to the treatment of the details. The joints of the wall tiles are jointed with white cement or special grout.
Kitchen and bathroom tiles vary
Since the kitchen and the bathroom are in the most contact with water, it is necessary to pay attention to waterproofing and moisture-proofing in the kitchen and bathroom. When choosing a tile, it must be particularly particular.
The industry insider told Mr. Zhou that the good ceramic tiles are completely resistant to the erosion of moisture and protect the walls, while still maintaining a clean and beautiful appearance for a long time. In general, when choosing tiles for kitchen and bathroom, matte finishes or tiles with embossed shapes are the best choice for non-slip. Secondly, we must also pay attention to the floor of the bathroom should be 10~20 mm below the floor of other rooms. Under normal circumstances, the laying of bathroom floor tiles should retain a 1% leakage slope, and the floor drain is the lowest to facilitate drainage. The joints of the floor tiles should be the same thickness and aligned with the wall tiles.
At present, the bathroom is still more popular "dry and wet partition". Simply put, it is the separation of the shower area from the toilet and the basin area. The dry zone and the wet zone can be divided into different tile materials and color varieties to achieve a good division, so that the two do not interfere with each other, avoiding splashing or other local pollution during bathing. (Hua Shangbao reporter / Li Tao)
White masterbatch
It was selected high-quality rutile type through a unique process refined.It has perfect whiteness, strong shading power, good dispersity, high plastic grease, good universal property,and so on. It was saled with reasonable price.and widely used in blowing film, pipe, injection molding, blowing bottle, wire drawing, casting, foaming, sheet and other plastic products industry.It is suitable for plastics raw material, such as PE, PP, PP, PVC, EVAPS, ABS, etc. Titanium dioxide content: 30- 70%
Universal White Masterbatch Granules
Universal White Masterbatch Granules,White Film Masterbatch Granules,White Board Masterbatch Granules,White Wire Masterbatch Granules
Cai Jian Plastic Product Co., Ltd. , http://www.caijianmasterbatch.com