Top Ten Problems Needing Attention in Tile Decoration Construction
1, tile soaked water on demand bubble now often see some customers go back unused tiles, the results found that some can not be returned, because the tiles bubble over the water. Manufacturers or businesses nowadays can not be returned in general, if there is no use of tiles that will cause unnecessary waste. Suggestions: How much foam to use, how much foam to build, how much foam to build, not to brew it all at once, and to combine the construction progress of the workers.
2. The tiles are made before the paving plan. Many of the workers in the construction plan are bricks but they are paved. When the paving reaches a certain degree, it is found that the tile bricks are not in a good condition and the proportions are inconsistent, so they are removed and re-paved. , causing unnecessary wear and tear. Suggestion: Make a paved brick plan before paving.
3. The correct selection of cement labels and mixing ratio of cement sand were used to contact many friends to reflect the cracking of the tiles. Some of them were caused by improper mixing ratio of cement sand or excessive cement markings, and the proportion of cement was high. The tile has strong adhesive force and the bricks can quickly stick, but the cement mixing ratio is high, and the expansion coefficient of the cement mortar is large, and it is easy to crack the tile after laying. The recommended ratio is 1:3 for wall tiles, 1:2-2-3 for floor tiles, and cement number 32.5 for cement.
4, tile processing should be careful when the special wall tiles in the touch Yang angle, the edging to be careful, do not damage the ceramic glaze layer, pay attention to the gap when the link, not too small.
5, when dealing with the flue or the wall when the wall must be standardized to deal with re-walling can not use Daxinban wall materials (this practice is known to be not feasible, but now the construction workers often deal with this, so as The owner must pay attention to the fact that the tiling will easily cause the tiles to fall off and crack.
6, the seams of the tiles can not be too small Tile joints are too small to reduce the service life of tiles, ceramic tiles in the thermal expansion and contraction when the crack glaze.
Recommendation: Whether it is a seamed tile or a seamless tile, be sure to pay attention to the remaining joints during construction.
7. It is necessary for the workers to notice the ceramic tile in construction. This is a place where the current decoration company has done relatively poorly. When this happens, especially when the material is not their recommendation, it will often continue construction. In fact, this approach is totally irresponsible. After all the paving, you find that there is a problem, it is more troublesome to deal with, the construction side and the material side of each other, and finally rework, this process will consume a lot of energy and financial resources. Therefore, during the construction, it is necessary to clearly tell the workers that if problems are found, they must be notified in a timely manner.
Recommendation: In order to avoid this situation, it is best to notice the problem in a timely manner, you can ask the seller and the construction side together to identify, do not drag things to the end of the final solution.
8, the best caulking after the tile is dry and then do the stitching Now many workers are in the tile after the paving began immediately, this treatment is very inappropriate, because the tile is not completely dry, in the jointing In the process, it is easy to cause the tiles to loosen, and the tiles will fall off in the later period, leaving potential safety hazards.
Advice: Tiles are allowed to dry before the tiles are dried. Normally any time after 24 hours.
9, the wall before the tiling to clean the wall Some irresponsible construction team in the paving the wall, the wall scraped the putty of the wall tiling, no putty shovel off directly on the brick, this approach The safety hazard is very large. Due to the large cement, the cement cannot be put on the putty, which can easily cause the tiles to fall off. This is also very insecure!
Suggestion: The wall surface must be inspected before tiling. If the wall has cracks, it must be treated first and the wall surface cleaned.
10. The tiles are protected during paving. Do not scratch the brick surface. The contaminated brick surface moves around the brick surface that is not solidified. The wall painting, the paint floor, and the protective film are not used in the construction process. It will happen, these will cause damage to the tiles.
1, tile soaked water on demand bubble now often see some customers go back unused tiles, the results found that some can not be returned, because the tiles bubble over the water. Manufacturers or businesses nowadays can not be returned in general, if there is no use of tiles that will cause unnecessary waste. Suggestions: How much foam to use, how much foam to build, how much foam to build, not to brew it all at once, and to combine the construction progress of the workers.
2. The tiles are made before the paving plan. Many of the workers in the construction plan are bricks but they are paved. When the paving reaches a certain degree, it is found that the tile bricks are not in a good condition and the proportions are inconsistent, so they are removed and re-paved. , causing unnecessary wear and tear. Suggestion: Make a paved brick plan before paving.
3. The correct selection of cement labels and mixing ratio of cement sand were used to contact many friends to reflect the cracking of the tiles. Some of them were caused by improper mixing ratio of cement sand or excessive cement markings, and the proportion of cement was high. The tile has strong adhesive force and the bricks can quickly stick, but the cement mixing ratio is high, and the expansion coefficient of the cement mortar is large, and it is easy to crack the tile after laying. The recommended ratio is 1:3 for wall tiles, 1:2-2-3 for floor tiles, and cement number 32.5 for cement.
4, tile processing should be careful when the special wall tiles in the touch Yang angle, the edging to be careful, do not damage the ceramic glaze layer, pay attention to the gap when the link, not too small.
5, when dealing with the flue or the wall when the wall must be standardized to deal with re-walling can not use Daxinban wall materials (this practice is known to be not feasible, but now the construction workers often deal with this, so as The owner must pay attention to the fact that the tiling will easily cause the tiles to fall off and crack.
6, the seams of the tiles can not be too small Tile joints are too small to reduce the service life of tiles, ceramic tiles in the thermal expansion and contraction when the crack glaze.
Recommendation: Whether it is a seamed tile or a seamless tile, be sure to pay attention to the remaining joints during construction.
7. It is necessary for the workers to notice the ceramic tile in construction. This is a place where the current decoration company has done relatively poorly. When this happens, especially when the material is not their recommendation, it will often continue construction. In fact, this approach is totally irresponsible. After all the paving, you find that there is a problem, it is more troublesome to deal with, the construction side and the material side of each other, and finally rework, this process will consume a lot of energy and financial resources. Therefore, during the construction, it is necessary to clearly tell the workers that if problems are found, they must be notified in a timely manner.
Recommendation: In order to avoid this situation, it is best to notice the problem in a timely manner, you can ask the seller and the construction side together to identify, do not drag things to the end of the final solution.
8, the best caulking after the tile is dry and then do the stitching Now many workers are in the tile after the paving began immediately, this treatment is very inappropriate, because the tile is not completely dry, in the jointing In the process, it is easy to cause the tiles to loosen, and the tiles will fall off in the later period, leaving potential safety hazards.
Advice: Tiles are allowed to dry before the tiles are dried. Normally any time after 24 hours.
9, the wall before the tiling to clean the wall Some irresponsible construction team in the paving the wall, the wall scraped the putty of the wall tiling, no putty shovel off directly on the brick, this approach The safety hazard is very large. Due to the large cement, the cement cannot be put on the putty, which can easily cause the tiles to fall off. This is also very insecure!
Suggestion: The wall surface must be inspected before tiling. If the wall has cracks, it must be treated first and the wall surface cleaned.
10. The tiles are protected during paving. Do not scratch the brick surface. The contaminated brick surface moves around the brick surface that is not solidified. The wall painting, the paint floor, and the protective film are not used in the construction process. It will happen, these will cause damage to the tiles.
Tile entrance decoration cement coating decorative decoration company paint
PCD Cutting Tool Blanks(PCD Disc)
BOHONG has world-class production facilities for PCD cutting tool blanks. BOHONG has advanced raw material inspection instruments (SEM), finished PCD testing equipment using ultrasonic scanning technology (C-SCAN), large-diameter PCD dics sintering capabilities, and proven PCD surface processing, polishing and cutting technologies.
Pcd Cutting Tool Blanks,Pcd Disc,Pcd Cutting Blanks,Pcd Blanks For Alloys
Henan Bohong New Material Co., Ltd , https://www.bohongpcd.com