When tiling, you still have to master some techniques, so that the effect of sticking out will be better, and those who have been decorated should have seen before, that is, tiles will be soaked in water before it is posted. The following Xiao Bian came to tell you about the tile soaked in water for 3 days and you can pay attention to what matters.
Tile soaked in water for 3 days
Since “bubble water†is said, the tile will be completely immersed in water when it is soaked. In general, a large basin will be used first. However, there are some unconscientious construction teams who use water pipes to spray water when they are constructing. By doing so, they can only soak tiles, and they simply cannot reach the full “drinking†of tiles. This is where various problems will arise. Tile soaked in water for 3 days can paste it , in fact, this is to be set according to different tiles, different tiles of different water absorption, so there is no a specific standard. But the end result is to make your home's tiles "drink" the water and stop blowing bubbles. That's fine. If you have high water absorption, it will take longer. For example, if it is humid in the rainy season, then it is possible to shorten the time accordingly; when the weather is dry, then the bubble time will be longer.
What are the matters that need to pay attention to tile soaking
1, water depth
The first thing to do is to choose a relatively large basin to tile the tiles so that there is enough water and the depth of water cannot be lower than the height of the tiles stacked in the basin.
2, stacked tiles
Put the tiles in the basin, and here you have to pay attention to the glaze facing up and the pottery facing down. If the glaze is facing downwards, it is easy for the tile corners to cause the porcelain to fall off due to bumps.
After the water is soaked, remember to remove the tile from the bowl and put the tiles on the glazed surface. Because if the glazed corner is easy to pick up porcelain. The best thing to do is to wrap the cartons on the floor mat so that the tiles can be placed against the wall.
3, soaking time
The water absorption rate of different tiles is not the same, so the time for soaking water is also different. For example, the higher the water absorption rate, the longer the water soaking time will be. Check if the tiles are "drinking water", then you can see if your bubble will bubbling.
4, water temperature
The water temperature of the tile can be as close to the room temperature as possible. Be careful not to use too low a water temperature, otherwise it will affect the tiles to absorb water.
4, how long after soaking water can paste
After the tile is “satisfiedâ€, you can take it out to dry at this time and it can be tiled when the tile surface has no watermark.
Summarize: About 3 days of tile soaking water and tile soaking water should pay attention to what matters related to the introduction to this, tile soaking water can be said before the paste is a very important step, if not for you tile foam Water, then there will be a variety of problems after use.
A bench-scale study was conducted using water from a drinking water treatment facility on Lake Ontario to investigate water quality and disinfection impacts of chlorine contamination in a chlorine dioxide solution applied for primary disinfection. Levels of chlorine contamination were varied between 0% (Pure Chlorine Dioxide) and 20%, with a chlorine dioxide dose of 1 mg/L. The chlorine did not significantly affect the rate of chlorine dioxide decay in the water. The chlorine reduced chlorite formation, but led to a corresponding increase in chlorate formation. Trihalomethane and haloacetic acid concentrations varied with the amount of free chlorine present in the chlorine dioxide solution. Levels of Bacillus subtilis endospore inactivation were similar for solutions containing pure chlorine dioxide and a 20%:80% chlorine:chlorine dioxide mass ratio (for the same total chlorine concentration). Since chlorine alone has been reported to be very ineffective against these endospores, the results suggest that the disinfection effectiveness of the mixture was greater than the effectiveness predicted from each of the two disinfectants acting alone.
Swimming Pool Water Disinfection
Clo2 Spa Water Disinfection, Bath Water Bacteria Disinfection, Water Disinfectant Chemicals For Swimming Pool, Swimming Pool Water Disinfection
Nanjing Ligong Shuifu Environmental Protection Technology Co.,Ltd. , http://www.watermanclo2.com